Product Description:Part: Steering Rack and PinionInterchange Part Number:Rack Description:Steering gear,also called steering gear, is the most important part of automobile steering system.Power steering (PAS) or steering assist system helps drivers steer by augmenting steering effort of the steering wheel. Power steering rack and pinion is the most important part for vehicle swerving and security assurance. It converts the rotational motion of the steering wheel into the linear motion needed to turn the wheels and provides a gear reduction, Power Steering Rack & Pinion For MERCURY MARINER 10-11,FORD ESCAPE 10-12 All
Part: Steering Rack and Pinion
Interchange Part Number:Rack 5178A
Steering gear,also called steering gear, is the most important part of automobile steering system.
Power steering (PAS) or steering assist system helps drivers steer by augmenting steering effort of the steering wheel.
Power steering rack and pinion is the most important part for vehicle swerving and security assurance.
It converts the rotational motion of the steering wheel into the linear motion needed to turn the wheels and provides a gear reduction,
thus making it easier to turn the wheels.
Compatible with the following vehicles:
FORD ESCAPE 2010 - 2012 All Models
MAZDA TRIBUTE 2008 - 2010 EXC. HYBRID
MAZDA TRIBUTE 2011 All Models
MERCURY MARINER 2010 - 2011 All Models
note:
1.In order to avoid the fault caused by the dirt entering the steering oil circuit, the plug on each oil port of steering pump of steering gear shall be opened before connecting the oil pipe, and the oil pipe and plug shall be carefully cleaned and deburred.
2. Turn the steering wheel to the straight ahead position.
3. Clean the mounting bracket of the steering gear and relevant mating surfaces of the steering gear.
4. For the adjustable steering column, use a suitable rope to pass through the space of the cross fork of the steering shaft, hang the steering shaft, and connect the steering shaft and the input shaft of the steering gear.
5. Turn the steering gear to the middle position to align the relevant marks at the input end and output end of the steering gear.
6. Install the steering gear on the mounting base and tighten the fixing bolts.
7. Universal joint or coupling between mounting column and steering gear.
8. For the adjustable steering column, the upper end seal of the steering gear shall not be damaged when the universal joint is installed.
9. Keep the steering wheel in straight ahead position.
10. Put the pitman arm on the steering gear to align the two marks. 10. Tighten the locknut according to the specified torque and rivet (anti loose pit)
Power Steering Rack & Pinion For MERCURY MARINER 10-11,FORD ESCAPE 10-12 All
Part: Steering Rack and Pinion
Interchange Part Number:Rack 5178A
Steering gear,also called steering gear, is the most important part of automobile steering system.
Power steering (PAS) or steering assist system helps drivers steer by augmenting steering effort of the steering wheel.
Power steering rack and pinion is the most important part for vehicle swerving and security assurance.
It converts the rotational motion of the steering wheel into the linear motion needed to turn the wheels and provides a gear reduction,
thus making it easier to turn the wheels.
Compatible with the following vehicles:
FORD ESCAPE 2010 - 2012 All Models
MAZDA TRIBUTE 2008 - 2010 EXC. HYBRID
MAZDA TRIBUTE 2011 All Models
MERCURY MARINER 2010 - 2011 All Models
note:
1.In order to avoid the fault caused by the dirt entering the steering oil circuit, the plug on each oil port of steering pump of steering gear shall be opened before connecting the oil pipe, and the oil pipe and plug shall be carefully cleaned and deburred.
2. Turn the steering wheel to the straight ahead position.
3. Clean the mounting bracket of the steering gear and relevant mating surfaces of the steering gear.
4. For the adjustable steering column, use a suitable rope to pass through the space of the cross fork of the steering shaft, hang the steering shaft, and connect the steering shaft and the input shaft of the steering gear.
5. Turn the steering gear to the middle position to align the relevant marks at the input end and output end of the steering gear.
6. Install the steering gear on the mounting base and tighten the fixing bolts.
7. Universal joint or coupling between mounting column and steering gear.
8. For the adjustable steering column, the upper end seal of the steering gear shall not be damaged when the universal joint is installed.
9. Keep the steering wheel in straight ahead position.
10. Put the pitman arm on the steering gear to align the two marks. 10. Tighten the locknut according to the specified torque and rivet (anti loose pit)
Item SpecificsBrand :SCITOOType :Steering Gear,Steering Gear Body,Steering Rack,Rack & PinionManufacturer Part Number :CB152252 S01OE/OEM Part Number :Rack 5178AInstallation method :Performance/CustomMaterial :High Quality SteelManufacturer Warranty :1 YearSurface Finish :Polished, Rust ProtectedFitment Type :Direct ReplacementCountry/Region of Manufacture :UnknownPerformance Part :YesVintage Part :NoUniversal Fitment :NoRack Material :corrosion and rust preventionNote :Backed by satisfying after-sales serviceAdvantage :Rotate quickly and normal positionOE Number :Power Steering Rack,Steering Rack and PinionSub Type :Rack and Pinion Assembly, Rack and Pinion Rack GearPackage :Dust plugItment Note :Top performance For long service lifeMounting Hardware Included :As the pictureItment Note :Top performance For long service lifeMounting Hardware Included :As the picture
Shipping
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
1. Package handling takes about 2 business days at our warehouse, so please make sure entering correct payment and shipping information before checking out. Once your payment is completed, we are not going to accept any more changes to your order.
2.All domestic orders will be shipped via USPS, UPS or Fedex from our US warehouse and usually arrives to your door in about 2-7 business days.
3.Local pick up is not available.
4.International Buyers C Please Note:
a. Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility.
b. Please check with your country customs office to determine what these additional costs will be prior to offerding/buying.]
Payment
[We only accept payment through PayPal. You can open a Paypal account at www.paypal.com.]
Returns
1.All of our brand new items come with a 60-Days money-back guarantee.
2.We define the item as defective only if it doesn't function as described, It is the buyer's responsibility to understand the item description before offerding.
3.We will replace the defective items, provided that they are in stock within the warranty period posted with the listing and the buyer return the original item and pay for the S&H cost for the replacement.
4.We will refund the purchase price if the replacement is not available or buyer prefers a refund and send the original item back at his/her own cost.
5.Shipping& handling cost are not refundable.
6.Man-made damage by abuse or wrong operation is not covered by this warranty.
7.No product liability insurance is assumed.
8.Refunds will be credited within 5 to 7 business days of receiving the return. When we've received and processed the return, we will refund the applicable amount minus any Recovery Fees (See Details Below) for the amount you paid for the item(s), plus any applicable sales tax. ]
Customer Services
Q: How do I pay for my purchase?
A: MY store accepts PayPal.
Q: When will the item be shipped out?
A: This item will be shipped with 2 business day once payment completed.
Q: Where is my tracking number?
A: Please log on your account, click "my "-->"my summary", or open your email box and find the shipping notification email.
Q: How do I return an item?
A: My tore accepts returns. Items must be returned within 60 days. Refunds will be given as money back. Please contact our customer service before you return an item. ]
response
1. We will leave positive response once we get your payment.
2. If you are dissatisfied for any reason, please do contact us before you leaving a response. We will work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave a response to all our customers.
3. If you are satisfied with the product you received, wish you can leave us a response.
New List Item For Kia Spectra Spectra5 2007 2008 2009 2.0L Fuel Pump Assembly USD 66.89 Exterior Door Handle Front Right For 2007-2011 Toyota Camry 2005-2015 Tacoma USD 15.41 For 2002-2004 ARCTIC CAT 500 Complete CV Axle Shaft Assembly 4PC Set USD 201.28 For 63-68 Ford Fairlane 63-67 Ford Galaxie 64-68 Ford Mustang Harmonic Balancer USD 46.99 For Ford F250 F350 6.4L High & Low Pressure Twin Turbo Cartridge CHRA Core Set USD 316.48 Shop CategoryStore Home A/C Expansion Valve ABS Wheel Speed Sensor AC Compressor AC Compressor Control Valve+A AC Condenser & Radiator◈AC Condenser◈AC Condenser & Radiator◈Radiator Adjustable Control /Camber Arm Air Cleaner Filter Box Air Diesel Heater Air Dryer Air suspension valves solenoid Air suspensions Alternators ATV Brake Caliper ATV Brake Master Cylinder ATV Ignition Switch ATV Rear Wheel Axle ATV Tires Auto parts◈Blower Motor◈Coilover◈complete struts◈CV Axle◈Fuel Pump Assembly◈Ignition Coil◈Key Case◈Starter◈strut/absorber shock◈Struts/Absorbers Shocks◈Towing Mirrors◈Trunk Floor Mats◈Window Switch ball joint Ballast module Bed Step Blower Motor & Resistor Brake Oil Hose Brake Pads & Rotors◈Brake Pad Sensor◈Brake Pads◈Brake Rotors◈Brake Rotors and Pads Brake System Parts◈Brake Calipers◈Brake Drums & Brake Shoes◈Brake Pads & Brake Shoes Bumper C Notch & Flip Kit Camshaft & Crankshaft Camshaft Position Sensor Car Antenna Car Carburetor Car Cover Car Seat Cover Car Tools Cargo Cover CDI BOX Consoles & Parts Control Arms & Parts Cooling Fan Cooling Fan Clutch Crankcase Vent Valve Crankshaft Position Sensor CV axle+Brake Pads/Rotors Cylinder Head Gasket Sets Cylinder Piston Gasket Kit Cylinder Piston Kit dash cover Dipstick Door check stop Door handle Door Lock Actuator Driveshaft Electric Water Pump Electrical & Test Equipment Engine Mount Evaporators Fastener Fender Flares fog lights Foot Rest PedalHot Item Inline Universal High Pressure Fuel Pump With Installation Kit 0580464070 USD 20.95 12V Universal Fuel Pump Gas Diesel Inline Low Pressure HEP-02A BHEP-02A USD 11.84 Alternator for 110Amp Chrome Street Rod GM 305 350 BBC SBC 1 Wire Self Exciting USD 67.71 Fuel Pump for Chevy S10 GMC Sonoma Hombre 4.3L 97-02 for Isuzu Hombre 4.3L 97-20 USD 33.39 2pc 3157 4114 4157 LED DRL Driving Daytime Running Light Bulbs 12SMD 6000K White USD 8.39 Picture
Power Steering Rack & Pinion For MERCURY MARINER 10-11,FORD ESCAPE 10-12 All
Part: Steering Rack and Pinion
Interchange Part Number:Rack 5178A
Steering gear,also called steering gear, is the most important part of automobile steering system.
Power steering (PAS) or steering assist system helps drivers steer by augmenting steering effort of the steering wheel.
Power steering rack and pinion is the most important part for vehicle swerving and security assurance.
It converts the rotational motion of the steering wheel into the linear motion needed to turn the wheels and provides a gear reduction,
thus making it easier to turn the wheels.
Compatible with the following vehicles:
FORD ESCAPE 2010 - 2012 All Models
MAZDA TRIBUTE 2008 - 2010 EXC. HYBRID
MAZDA TRIBUTE 2011 All Models
MERCURY MARINER 2010 - 2011 All Models
note:
1.In order to avoid the fault caused by the dirt entering the steering oil circuit, the plug on each oil port of steering pump of steering gear shall be opened before connecting the oil pipe, and the oil pipe and plug shall be carefully cleaned and deburred.
2. Turn the steering wheel to the straight ahead position.
3. Clean the mounting bracket of the steering gear and relevant mating surfaces of the steering gear.
4. For the adjustable steering column, use a suitable rope to pass through the space of the cross fork of the steering shaft, hang the steering shaft, and connect the steering shaft and the input shaft of the steering gear.
5. Turn the steering gear to the middle position to align the relevant marks at the input end and output end of the steering gear.
6. Install the steering gear on the mounting base and tighten the fixing bolts.
7. Universal joint or coupling between mounting column and steering gear.
8. For the adjustable steering column, the upper end seal of the steering gear shall not be damaged when the universal joint is installed.
9. Keep the steering wheel in straight ahead position.
10. Put the pitman arm on the steering gear to align the two marks. 10. Tighten the locknut according to the specified torque and rivet (anti loose pit)
Item SpecificsBrand :SCITOOType :Steering Gear,Steering Gear Body,Steering Rack,Rack & PinionManufacturer Part Number :CB152252 S01OE/OEM Part Number :Rack 5178AInstallation method :Performance/CustomMaterial :High Quality SteelManufacturer Warranty :1 YearSurface Finish :Polished, Rust ProtectedFitment Type :Direct ReplacementCountry/Region of Manufacture :UnknownPerformance Part :YesVintage Part :NoUniversal Fitment :NoRack Material :corrosion and rust preventionNote :Backed by satisfying after-sales serviceAdvantage :Rotate quickly and normal positionOE Number :Power Steering Rack,Steering Rack and PinionSub Type :Rack and Pinion Assembly, Rack and Pinion Rack GearPackage :Dust plugItment Note :Top performance For long service lifeMounting Hardware Included :As the pictureItment Note :Top performance For long service lifeMounting Hardware Included :As the picture
ShippingPaymentReturnsCustomer Servicesresponse
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
1. Package handling takes about 2 business days at our warehouse, so please make sure entering correct payment and shipping information before checking out. Once your payment is completed, we are not going to accept any more changes to your order.
2.All domestic orders will be shipped via USPS, UPS or Fedex from our US warehouse and usually arrives to your door in about 2-7 business days.
3.Local pick up is not available.
4.International Buyers C Please Note:
a. Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility.
b. Please check with your country customs office to determine what these additional costs will be prior to offerding/buying.]
[We only accept payment through PayPal. You can open a Paypal account at www.paypal.com.]
1.All of our brand new items come with a 60-Days money-back guarantee.
2.We define the item as defective only if it doesn't function as described, It is the buyer's responsibility to understand the item description before offerding.
3.We will replace the defective items, provided that they are in stock within the warranty period posted with the listing and the buyer return the original item and pay for the S&H cost for the replacement.
4.We will refund the purchase price if the replacement is not available or buyer prefers a refund and send the original item back at his/her own cost.
5.Shipping& handling cost are not refundable.
6.Man-made damage by abuse or wrong operation is not covered by this warranty.
7.No product liability insurance is assumed.
8.Refunds will be credited within 5 to 7 business days of receiving the return. When we've received and processed the return, we will refund the applicable amount minus any Recovery Fees (See Details Below) for the amount you paid for the item(s), plus any applicable sales tax. ]
Q: How do I pay for my purchase?
A: MY store accepts PayPal.
Q: When will the item be shipped out?
A: This item will be shipped with 2 business day once payment completed.
Q: Where is my tracking number?
A: Please log on your account, click "my "-->"my summary", or open your email box and find the shipping notification email.
Q: How do I return an item?
A: My tore accepts returns. Items must be returned within 60 days. Refunds will be given as money back. Please contact our customer service before you return an item. ]
1. We will leave positive response once we get your payment.
2. If you are dissatisfied for any reason, please do contact us before you leaving a response. We will work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave a response to all our customers.
3. If you are satisfied with the product you received, wish you can leave us a response.
