4PCS Front Rear Shock Strut Assembly For 2007-2016 Toyota Tundra Limited SR5 For Sale - New and Used

When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

4PCS Front Rear Shock Strut Assembly For 2007-2016 Toyota Tundra Limited SR5:
$84.03

✈Compatibility Chart

1, You can distinguish specific model of an automobile by VIN(Vehicle Identification Number).

2, VIN(Vehicle Identification Number) consists of total 17 English letters and arabic digits.

3, VIN does not include the letters I (i), O (o), and Q (q) (to avoid confusion with numerals 1 and 0).

2007-2016 Toyota Tundra

✈OEM Part Guideline

Step 1: Before you lift the vehicle, loosen lug nuts one full turn.

Step 2: Jack up vehicle and use jack stands for safety & remove the tire from the rotor.

4PCS Front Rear Shock Strut Assembly For 2007-2016 Toyota Tundra Limited SR5

✈Compatibility Chart

1, You can distinguish specific model of an automobile by VIN(Vehicle Identification Number).

2, VIN(Vehicle Identification Number) consists of total 17 English letters and arabic digits.

3, VIN does not include the letters I (i), O (o), and Q (q) (to avoid confusion with numerals 1 and 0).

2007-2016 Toyota Tundra

✈OEM Part Guideline

Step 1: Before you lift the vehicle, loosen lug nuts one full turn.

Step 2: Jack up vehicle and use jack stands for safety & remove the tire from the rotor.

Step 3: (Wheel alignment is necessary after strut replacement.) Marking the position of all the bolts will help

keep the alignment close to original and save time aligning. Use a colored pencil to mark the old strut on the bolt.

Step 4: Use penetrating oil (such as WD40) to coat any rusted fasteners, let soak for approximately 1 hour.

Step 5: (Optional) While waiting for oil to soak, take this time to inspect all other components that may need

replacement (brake pads, rotors, brake hoses, ball joints, CV boots, tie rod ends, bushings, sway bars, etc).

Step 6: Remove any brake line or wire attachments from the strut body. Do not disconnect brake lines (if possible)!

Opening brake lines will require bleeding of the brake system.

Use extreme caution when removing brake lines from your struts, as any damage to your brake line can result in

expensive and time consuming repairs.

Step 7: Remove sway bar attached to the strut assembly or control arm.

Step 8: Remove the tie rod (only if it attached to the body of the strut, if not leave it attached to the steering knuckle).

Step 9: Remove the strut to knuckle bolts at the bottom of the strut. On some vehicles, the brake caliper and rotor

may need to be removed to gain access.

Step 10: Remove the upper mounting plate bolts located in the engine or trunk compartment. Do not remove the

center retaining nut! It is not safe to unload the spring from the assembly in this position.

Step 11: Carefully remove the old strut assembly from the vehicle. Be very cautious not to let the strut "drop" down

on your brake line, rotor or drum.

Step 12: Install the new Complete Strut Assembly in the reverse order as above (steps 11-6). Using an anti-seize

compound on all fasteners is suggested.

Step 13: Carefully double check your work and make sure everything is tightened to manufacturers torque specifications.

Step 14: Replace the tire the rotor and tighten to manufacturers torque specifications.

Step 15: Slowly lower the vehicle down after removing the jack stands. Pay very close attention to any odd sounds

when the vehicle is lowered onto the new Complete Strut Assemblies.

Step 16: It is very important that you immediately "road test" your vehicle right away to ensure that installationwas done properly.

Listen and feel for common signs of incorrect installation while driving slowly over speed bumps, rough road or potholes.

✈Removal Guideline

Installation is in reverse order of Struts Shocks removal.

✈Features and Benefits

Hardened Rods & NOK Seals;
Precision Robotic Welding;
Top Factory Certifications;
Premium Powder-Coated Finish;
Damper Engineered for Each Vehicle Application's
OE or Better Performance Level

✈Item Specifications

Key Words:4PCS Front Rear Shock Strut Assembly For 2007-2016 Toyota Tundra Limited SR5
Package Includes:2Pairfor Front Rear Left andRightStruts Shocks

Notes: Please double confirm the compatibility as well as the OEM number before purchasing.
Instruction is not included. Professional installation is recommended.

The struts/shocks are nitrogen gas charged and tuned for each specific vehicle application.
They will greatly improve the ride, handling,and safety of your vehicle!

Item SpecificsBrand cfspeed-autopartsManufacturer Part Number C80857601APSType StrutFitment Type Direct ReplacementPlacement on Vehicle LeftManufacturer Warranty 1 YearFeatures AdjustableModified Item NoAdjustable NoGas Charged Shock YesInterchange Part Number 341480,349054OE Part Number 71119,37298Kit or Single Part KitKit Parts Included Set of two front struts and two rear strutsSurface Finish Powder CoatOE Spec or Performance/Custom OE SpecColor Gloss BlackReturn Policy Free return or replacement within 30 daysShock Absorber System Double PipeShock Absorber Type GasVintage Part NoMaterial SteelMounting Style Screw-OnPerformance Part NoQuantity 4PcsSuperseded Part Number Shock and StrutUniversal Fitment NoCompressed Length 17.760"(F),15.000"(R)Travel Length 5.760"(F),9.380"(R)Included Hardware Mounting HardwareItem Length 23.520"(F),24.380"(R)Package Dimension (in.) 26.57*8.66*4.72 (F), 24.41*6.3*3.54 (R)Gross Weight (LB) 30.424Package Dimension (in.) 26.57*8.66*4.72 (F), 24.41*6.3*3.54 (R)Gross Weight (LB) 30.424

Payment

PayPalpreferred.

We are dedicated to provide high quality products and satisfied customer service to our sincerely customers, so if there's any questions or problems with our products or service, feel free to contact us please.