Hooker Blackheart 8505HKR LS Swap Exhaust Manifolds - Rear Exit For Sale - New and Used

• Our store
• About Us
• Contact Us
• Add to Favorite Sellers

Hooker BlackHeart LS Swap Exhaust Manifolds - Rear Dump - Natural Cast 8505HKR

Multi-Fit - GM Gen III/IV LS Engines - 2.50-in. Outlet. For applications or projects where our standard LS swap manifolds (8501HKR, 8502HKR, 8503HKR series) don\'t quite fit and our \"center dump\" manifold (8504HKR) exits too far forward, our new \"rear dump\" cast iron swap manifolds have arrived. These differ in that they exit in a straight-down fashion much like a block hugger header but exit more toward the rear of the engine than our \"center dump\" manifolds. Cast out of the same Hi-Silicon-Moly Ductile Iron as most of our other lines, it will be tough to find a more durable, streamlined, and quiet exhaust option. Available in natural cast, silver ceramic, or black ceramic finishes, these manifolds are offered with flanges, gaskets, and flange hardware for connecting to our lineup of adapter pipe kits. This not only allows for the easy addition of catalytic converters but also makes it simple to connect to our many exhaust system options.. NOTE: Not compatible with 2004-2006 GTO in an engine with ceramic-coated versions of these manifolds will most likely result in damage to the coating and VOID all warranties providing coverage to it. HOOKER™ recommends using bare cast-iron manifolds or an old set of headers to break-in engines to avoid coating damage. _x000D__x000D__x000D_Ceramic-coated manifolds require several heat cycles to fully cure before they will withstand extreme heat, so care should be taken to provide a series of 4 to 5 intermittent heat cycles to \"set\" the coating prior to putting the vehicle into service. An incremental increase in run duration and throttle angle should be added to each successive cycle; initial and final run durations between approximately 1 and 7 minutes will be sufficient to set the coating.

• 2.5-inch outlet diameter offers improved flow for maximum performance from a cast iron exhaust manifold
• Tight tuck design that provides an exit between our standard swap manifolds and center dump manifolds (see pictures for diagram and specs)
• Intended for GM LS engine swap applications where durability, quiet operation, and leak-free sealing is desired
• Available in Natural as-cast finish for a factory appearance, silver ceramic, or black ceramic
• Cast from Hi-Silicon-Moly Ductile Iron to provide durability and corrosion resistance
• Perfect complement to Hooker engine swap mount plates and Holley engine swap oil pans
• Hardware included: Nickel plated steel mating flanges, MLS mating flange gaskets, and mating flange hardware
• Similar to SBC driver side manifold (8525HKR) - same exit centerline but raised up 1.36-inches

General Policies

Warranty & Return Policy

• Holley Performance Products warrants new products to be free from defects in material and workmanship for a period of 90 days from date of purchase. Many items may have longer warranties please see Item Specifics above or contact us for information.
• Holley Performance Products Limited Warranty specifically does not apply to items or products, which have been (a) modified or altered in any way; (b) subjected to adverse conditions, such as misuse, neglect, accident, improper installation or adjustment, dirt or other contaminants, water,corrosion, or faulty repair; or (c) used in other than those applications recommended by Holley Performance Products. Holley Performance Products also does not warrant, and disclaims all liability for products used in racing activities and/or applications other than those specifically recommended in the current brand catalog.
• Warranties do not apply to items sold as Used. We want to make sure that every customer is completely satisfied with their purchase. Although obsolete, scratch & dent and used items do not have a warranty, we understand that things happen and every situation is different. Please let us know of any issues you may have before leaving response so we have an opportunity to make things right. We will do everything possible to make sure you are fully satisfied with your purchase and we want to earn your continued business!
• Buyer pays return shipping

Shipping & Tracking

• Please see the “Shipping and Payment” tab
• We ship all US orders via United Parcel Service (UPS Ground)
• A signature is required on all UPS orders over $750
• Tracking information will be sent via email after your package ships (you must supply a valid email address during checkout)
• We ship within 1 business day upon receipt of payment
• We do not ship to APO/FPO or US Post Office Box addresses
• We can not ship as a \"GIFT\" or ship anything internationally with changes to the invoice

Customer Service & response

• Our customer service hours are 8:00 am – 5:00 pm Central Time Monday thru Friday (excluding holidays)
• If you are not certain about an item or have questions, use the “Ask Seller a Question” link under the listing. We strive to answer questions submitted thru ’s message system within 1 business day
• We want you to be completely satisfied with your purchase – please let us know if you have any problems with your purchasebefore leaving responseso we have a chance to make it right – we want your repeat business!

Check out the official Holley Performancestorefor more great deals!!!

---