Kit to fit Stanadyne* Roosa Master* Diesel Injection Pumps.
NOTE: With all Stanadyne / Roosa Master Pumps, it is a goodpractice to tie the throttle lever in Wide Open position anytime the pump isgoing to be off the engine.
Stanadyne* Part Number 24371*
This kit fits many pump applications for John Deere, Case, International Harvester, just to name a few.
There are hundreds of applications that this kit will work.
These are aftermarket kits are OEM quality, There are actually better in my opinion
Also inside this kitare the line washers and drive seals needed for installation. As well as the "well know Flex-Ring" which is the culprit of pump failure most of the time.
This kit DOES fit all pumps with model numbers that start kit DOES NOT fit pumps with model numbers that start align="center">Tips for installing your flex ring (Please refer to included picture):Using snap ring pliers (1) Gently stretch one hole over one of the rivets in the cages first. (2)Then Move across and do the same to evenly spread the ring (3)Then finish out putting it over the remaining rivets. (4)
Please send us your complete pump model number if you are not sure if this kit is right for your application.
8007367440
dieselitems.
M – F 7:30 - 4:30 CT
"Jason will be your pump man if you let him"
From a Customer who Found Us on : "Just a note to let you know that the injector pump that you re-built for me works like brand new. If there is anyone here that needs one re-built I will tell them you are THE BEST IN THE COUNTRY". Thank You so much Ken - AZ
I rebuild and set these pumps for a living, and have been doing so for 40 years, If you would like to send me your pump to be rebuilt, contact me. Most of the pumps that use this kit will run about $450.00 to be rebuilt. We can also check and clean your injectors for free, so send them along as well. After checking your injectors, we can give a quote if any fail testing.
Here are some of things that can effect the price:
- Pump is locked up and/or the main drive shaft is broke.
- Engine will not start when warm, after sitting from 1-60 minutes. But does start when cool. This may indicates a bad head and rotor.
- Cam ring in pump is worn, requires inspection during tear down.
- Pump has excessive rust and corrosion.
- Housing is damage or unusable.
Here is how it works:
- Contact me with your pumps Models numbers.
- I will try to give you a closer estimate based on the problems you describe.
- Pump must not have been taken apart.
- Pump must be drained of all fuel as shipping service may return or destroy packages that leak fuel.
- You ship your pump to me pre-paid. (Packaged well, I can not be responsible for items damaged in shipment)
- We check the pump and contact you with a full estimate, return shipping cost and time you should expect your pump back. (Normal times are a week to 10 days).
- If you choose not to have your pump rebuilt after the estimate, all you pay is freight back to you.
Why would you want to do this?
- Pump will be cleaned, inspected, rebuilt, tested and will look and run great.
- All fully rebuilt units are invoiced and include a 6 months warranty.
- We will provide tips for reinstalling as well as some of the parts youmay need to do so.
- We have access to parts, specifications and test equipment to make sure your pump is right.
Remember the call is free, the service is great andmy knowledge base covers over 40 years. DC pumps are higher
Payment for rebuilt pumps must be paypal or Credit Card before we can ship the pump back to you, Thanks.
These are examples of complete pump Model Numbers:
DC pumps are higher
JDB 435AL-2415
DBGVC633-1AJ
DBM
DBO
Please Note: Your fuel injection pump is a very technical devise. Not only does it control your engine it also protects it as well. Repairing your pump yourself is a great way to save money. However, extra care must be used as serious pump and or engine damage can occur. A person repairing their own injection pump is assuming their own risk.
* Name and Numbers are used for reference purposes only And items are not the products of these
