K03 Turbo Turbocharger For Ford Escape Focus Fusion Taurus Lincoln MKC MKZ 2.0LINTERCHANGE PART NUMBERS:14031313-101, 14031313-102, 14031313-103, 14031313-104, 14031313-105, 2N-235, 2T-235, 5303 970 0272 ; 5303 970 0286, 5303 970 0287 ; 5303 970 0368, 5303 970 0420 ; 5303 970 0446, 5303 970 0507 ; 5303 998 0507, 53039700272 ; 53039700286, 53039700287 ; 53039700368, 53039700420 ; 53039700446, 53039700507 ; 53039880368, 53039980507 ; 847-1472, CJ5E6K682BA ; CJ5E-6K682BA, CJ5E-6K682-BA, CJ5E6K682CA ; CJ5E-6K682CA, CJ5E6K682CC, CJSE6K682CE, CJ5E-6K682-CC, CJSE-6K682-CEFITS THE FOLLOWING :2013-2015 Ford Escape SE Sport Utility 4-Door
2013-2013 Ford Escape SEL Sport Utility 4-Door
2013-2015 Ford Escape Titanium Sport Utility 4-Door
2013-2016 Ford Focus ST Hatchback 4-Door
2013-2016 Ford Fusion SE Sedan 4-Door
2013-2016 Ford Fusion Titanium Sedan 4-Door
2013-2016 Ford Taurus Limited Sedan 4-Door
2013-2016 Ford Taurus SE Sedan 4-Door
2013-2016 Ford Taurus SEL Sedan 4-Door
2015-2015 Lincoln MKC Base Sport Utility 4-Door
2015-2016 Lincoln MKC Black Label Sport Utility 4-Door
2016-2016 Lincoln MKC Premiere Sport Utility 4-Door
2016-2016 Lincoln MKC Reserve Sport Utility 4-Door
2016-2016 Lincoln MKC Select Sport Utility 4-Door
2013-2016 Lincoln MKZ Base Sedan 4-Door
2015-2016 Lincoln MKZ Black Label Sedan 4-DoorNOTED:Please check the Turbo Model, Turbo Part Number and OEM Part Number on your turbo to make sure it's the right one for your engine.
If you are not sure about these information, please feel free to contact usITEM INCLUDING:1.Turbocharger2.Gasket Kits3.Instructions4.White Gloves5.Flow report6.Foam filling material7.Balancing report8.LubricatorCHECKLIST :Before fitting the turbocharger:
1. Use new and approved gaskets at the various air, oil and exhaust connections to the turbocharger. Liquid gasket or sealants are not recommended, particularly for oil fittings.
2. Use a high temperature anti-seize compound on all threaded fasteners connected to the turbocharger.
3. Fill the turbocharger oil inlet port to overflowing with clean engine oil before connecting the oil feed hose.
When fitting the turbocharger to the manifold and connecting the respective pipes:
- 1. Before connecting the oil drain hose, crank the engine without firing until steady stream of oil flows from the drain port.
- 2. Operate the engine at low idle for at least three minutes after completing the installation of turbocharger. This will prevent oil starvation damage to the bearing system.
Turbocharger Installation Notice:
- Misuse or modification of the turbocharger can result in serious injury and property damage. Basic safety precautions including the following should always be followed:
- 1. Read and comply with all instructions including the “Checklist ” before installing or using any turbocharger.
- 2. Failure to follow these instructions will lead to premature failure of the turbocharger.
- 3. Only install the turbocharger on an engine which has been approved for such application. The turbocharger is a precision built product which has been matched and tested for use on specific engines only.
- 4. No part of the turbocharger may be altered as it may damage the engine.
- 5. Do not modify or substitute any parts of engine except in accordance with engine owner’s manual. Do not modify the engine fuel control system or restrict the inlet or exhaust system (see engine owner’s manual).
- 6. Do not operate at excessive altitudes (consult Engine Owner’s Manual for altitude restrictions).
- 7. Be sure that oil supply and drain lines are adequate. (See “Checklist ”.)
- 8. Always warm up the engine for 2-5minutes to allow oil to reach the turbocharger before operating under load.
- 9. Perform all maintenance specified by the engine manufacturer each time or at the recommended intervals. Concurrently inspect turbocharger for any deficiencies.
Why Choose Us？Practical Application
We value the performance of our parts in practical applications. This is our intention to acquire experienced tuning shops. We have the most senior mechanics, the most advanced testing equipments to help us constantly improve the production technology.
US Offices and Warehouse
We owns our warehouse and branch offices in United States, Australia and Germany, customer could receive product soon after purchase it.
Packages & Cooperative Carrier
Our package's filled with shock-ab-sorbing foam to protect the product maximumly and cooperate with major international logistics companies, the package will be delivered you at the best and reassuring way.
Professional Customer Communication
We have own service team.If there's any problem,please feel free to communicate. We'll try our best to help you.
If the product you receive is not the one you ordered, please take photos of any visible part numbers of visual reference and contact us directly; photos must be CLEAR and have the part numbers VISIBLE. Logistical claims must be filed within 30 days of received the product; exchanges in these cases will be handled promptly and at?no cost to the customer.
In order to process a return or exchange, please call us or send us a message through and we will be happy to assist you immediately.
However，any return that is NOT defective or NOT received in error, is the responsibility of the customer. We DO NOT cover any shipping costs and/or additional fees associated with the transaction.
