Immobilizer 2.4G Wireless Anti-Hijacking Engine Lock Car Alarm System Intelligent Circuit Cut Off Device Smart RFID Key
Main Features:Applicable models: 12V gasoline carInstallation location: Connected to the oil pump circuit or ignition switchProduct function: Automatic fuel cut-off and flameout or automatic power cut-offand flameoutProduct features: 2.4GHZ high RF identification technology, easy to install, andstable performance1. Anti-hijacking(robbery) function mode: (without short circuit ring inserted on the unit) Factory default After receiving the signal, the unit can start the car engine normally. The unit cannot receive the signal for 30-40 seconds, and the buzzer sounds once per second. If the signal is not received for 41 to 50 seconds, it will sound twice per second. Unable to receive signal for 51 to 60 seconds, 3 sounds per second. After 60 seconds, if the signal is not received, the engine will turn off and the buzzer will not sound.2. Directional dormant lock function mode: (insert short circuit ring on the unit) 1)When the car starts the engine, the unit receives a signal within 25 seconds, the buzzer sounds, and the car starts normally. Within 25 seconds, the unit cannot receive a signal and the engine shut down. 2) When starting the engine for the second time, the unit receives the signal and can start normally. If the unit still cannot receive the remote control signal, the engine will shut down after 20 seconds. 3)Start the engine for the third time (or more), as long as the unit receives the signal, it can start normally. If the unit cannot receive the signal, the engine cannot start, It is not possible to start normally until receiving a signal from the remote control. 4)The remote control signal is no longer sensed midway, and only when the engine is turned off and restarted, the signal needs to be re sensed.3.New technoloty 2.4Ghz RFID engine lock for 12V vehicle4. Intelligent NO scan card lock and unlock the car engine automatically5.Anti-hijacking (Anti-robbery) intelligently6. Engine circuit cut off intelligently7.Two thin transmitter8.The car engine will be locked automatically and could not be started beyond 2 (-8)meter9.Approch to the car within 2 meter, the engine will automatically unlock10.You can put the remote inside pocket, the engine will automatically lock and unlock11.Anti-hijacking mode, intelligent circuit cut off12.Without the remote, even use the car key can not start the engine13.Emergency release: if the remote lose or the remote is with low power, press the reset button for 3 times and keep press the button at the third time until the buzzer of the main unit chirp 3 times14.Very easy to installSpecification:Remote control instantaneous working current: ≤ 10mARemote control standby current: ≤ 3uARemote control battery specification: CR2032Remote control frequency: 2.4GHzOperating voltage of the unit: 12V ± 3VUnit standby current: ≤ 18mAUnit control current: ≤ 30AControl box size: 6 x 2.4 x 1.5 cm (L x W x H)Remote Controller size: 5.4 x 2.9 x 0.55 cm (L x W x H)Weight:0.12KGPacking size:160*92*50mm ,50PCS/canton ,canton size:MEAS:41*34*40CM
About installation:The product need installed by the Profesionales with Car electrician certificatedFor 12V DC car (Vehicle)The item without central door lock function ,only control the enginePackage Include:1x Main Control Unit With Wire2x Remote Control1x English User ManualM505 FAQ1. Can this product be used to control 24V trucks?At present, this product can only control 12V products, including cars, motorcycles, etc2. Is the product easy to install?This product is easy to install. The buzzer and Manual fire alarm activation are well matched, and no wiring is required. Directly connect the red and black power cables, with the black iron (negative) and the red connected to the positive (long-term) of the power supply. Two thick green wires are connected to cut off the two ends of the circuit or oil circuit to be controlled.3. I connected the positive and negative terminals of the power supply, but how can\'t I test whether the product relay is on or off?The red and black wires are the power supply terminals of the host, and the relay and buzzer are powered from the green wire. Therefore, at least one of the green wires must have 12V power to work. This is designed considering that the relay cannot work for a long time and consumes electricity when the car is turned off, and can only work while driving.4. How do the manual and automatic modes of the remote control work? How to distinguish?A. The manual mode of the remote control only emits signals when the remote control button is pressed, and does not emit signals until the button is pressed. Automatic mode is the automatic transmission of signals every few seconds.B. When pressing the remote control button in manual mode, the LED light will be on, and it will not light up if not pressed. In automatic mode, press the remote control button and the LED will flash several times.5. How to distinguish between the anti robbery (Anti-hijacking)mode and the Directional dormant lock function mode of the host?A. Anti robbery mode(Anti-hijacking) means that the host must continuously receive signals from the remote control. If the host does not receive the signal for 1 minute, it will turn off. Therefore, the remote control must continuously transmit signals to the host, which means that the remote control must be in automatic mode. (Turn off when leaving the remote control)B. The Directional dormant lock function mode requires receiving a signal from the remote control when powered on (ignition), and does not require continuous signal reception during the process and will not turn off. Therefore, the remote control can be in manual mode (press the remote control button once after each startup) or automatic mode. (Starting requires remote control signal)6. My car makes a noise half a minute after starting and then stalls one minute later. What is the reason why it cannot start again and how can I solve it?This issue is caused by the host not receiving the signal from the remote control, as the remote control has not turned on automatic mode. Simply turn on automatic mode.7. How far is the reception distance between the host and the remote control?This distance can be adjusted through the remote control. The power of the remote control is set to the lowest gear at the factory, with a distance of approximately 8 meters. The distance between the middle gear and the highest gear will be further. Generally, the distance is suitable without further adjustment. The significantly shorter distance can be solved by replacing the battery.8. Is the product a control circuit or an oil circuit?Both the oil circuit and circuit can be controlled, and the internal control of the host is the on and off of the relay.9. What is the current controlled by the host?The maximum control current is 30A
